Pro Polymer™ (Gel Maker)

Pro Polymer™ (Gel Maker)


act as Gel Maker It is able to withstand high electrolyte and can be used in a wide pH range of 2 - 8. It has a texture similar to that of hyaluronic acid, which gives a tacky sensation during the first 30 seconds of applying on the skin. Then a thin coating is applied. when completely dry

Price 58.00 ฿ This special price only valid for web order

gram (mininum 10 gram)

Unit price will be cheaper for larger size
The price will be calculated based on the size you enter


piece(s), Packing Cost : 10฿/pcs
The product will be packed based on the requested quantity

Expiration: 09/2024 (Lot: 6A075Q)

Add to cart Favorite PDF

  • Info
  • Documents
  • Technical

Pro Polymer, a gel-forming agent. special is with the mechanism of creating a gel texture to have a Polymeric structure


Pro Polymer can be used in scrub formulas, skin scrubs that require beads. because it can create a gel texture with high viscosity in order to be able to detain the beads from precipitating without causing sticky skin


Pro Polymer can create a creamy pudding. (cream or gel that looks like a pudding) using a high amount >3%


Pro Polymer has a texture similar to that of hyaluronic acid, with a tacky sensation in the first 30 seconds of application. Then a thin coating is applied. when completely dry


Pro Polymer is highly electrolyte resistant.


What is an electrolyte and if there is an electrolyte in the formula, what should be done?  

An electrolyte is any substance that contains Sodium, Magnesium, Calcium, Potassium, such as Sodium Lactate, Sodium PCA, Natural Moisturizing Amino Acids (due to the content of Sodium PCA), Zinc PCA including many types of natural extracts Because these natural extracts are often Sodium/Magnesium/Calcium/Potassium in the plant)

When creating a cream with electrolyte in the formula, the cream will soften (more liquid). The viscosity of the cream can be increased by using Pro Polymer™ in larger quantities (e.g. from normal 1% must be increased to 2-3%)


additional steps If the formula contains a large amount of electrolyte

To mix according to the various steps until the end. Separate the electrolyte-containing ingredients first, e.g. in formulas containing Sodium Lactate, Sodium PCA,Zinc PCA, then separate these ingredients. Do not rely on mixing at any stage. By allowing it to mix to get a complete gel first. Importantly, Pro Polymer should be used in a larger amount than usual. For example, usually 1% is used to get the desired thick gel texture. If there is an electrolyte group, then add Pro Polymer to 2-3% (depending on the amount of electrolyte mixture used). After gelling is complete. Add these electrolyte-containing ingredients to the formulation and observe the change in gel texture. If it's too soft, you can add more Pro Polymer later, but if you add Pro Polymer later, it will take time to dissolve and create a gel. and more spinning power or people


Use: as a thickener to create a gel texture to the water-based gel formula and create a creamy texture in the water + oil formula

Mixing method: Mix in water (water-phase) by spreading the powder on the liquid to increase the viscosity and stir for 3-5 minutes, no need for cooling or heating. Poor people get a smooth, even gel texture. should not over spin 2500 rpm This will damage the polymer and weaken the formula.

Usage rate: 0.5-5% (used in an increased amount when there is more Electrolyte in the formula, 0.8% recommended for general gel. high level of use The resulting gel will be hard, like a pudding, not suitable for general use.)

Product characteristics: white powder, light weight

Solubility: can dissolve in water

Storage: can be stored at room temperature But close the lid of the bottle tightly. Then completely protected from sunlight or heat, do not expose to moisture. (Please store in an envelope that comes with a moisture-proof envelope). The product has a shelf life of at least 2 years. *In case of exposure to moisture. The substance will coagulate. which can still be used but will take much longer to blend or stir to dissolve*




Storage: 15-30C, Hygroscopic! Avoid moisture.

Shelf Life: 36Months from manufacturing or testing date (Current Lot will expire: 09/2024)

Dosage (Range): 0.5% - 5%

Recommended Dosage: 1%

Research & Development: France

Mix Method: Add into water phase. Heat tolerant.

Heat Resistance: Avoid heat above 80C

Stable in pH range: 2 - 9

Solubility: Dispersible in water

Product Types: Cream , Lotion , Clear Gel , Mask


Product Specification:

Test Specification
White powder to slightly coloured Conforme
2% 25 degree Celsius Viscosity 30000-60000 mPa.s
2% Nacl+2 % 25 degree Celsius Viscosity 20000-50000 mPa.s
2% pH 3.0-6.0
Solid Content 90.00-100.00 %


No products

Shipping 0.00 ฿
Total 0.00 ฿